Academic Programs

Auto Mechanic I (CRT.AUTO)

This program prepares students with entry-level skills and knowledge of basic maintenance, electricity, engine and vehicle management systems, engine repair and brake systems needed in the automotive repair industry. Students gain valuable hands on knowledge to prepare them for a career as an automotive technician as well as ASE (Automotive Service Excellence) certification. Instruction is provided by ASE certified instructors with a shop/lab that is equipped with modern equipment. Lab manual expense is approximately $340. A list of recommended tools can be obtained from counselors or automotive instructors. Program requirements may change over time. Specific degree/graduation requirements are determined by a degree audit.

Request Info

Catalog Term Year: 2023 Spring

View As:

First Year
First Semester

COREAUT-048

Credit Hours: 2.00

COREAUT-050

Credit Hours: 5.00

COREAUT-051

Credit Hours: 4.00

COREAUT-080

Credit Hours: 4.00

First Year
Second Semester

COREAUT-052

Credit Hours: 5.00

COREAUT-053

Credit Hours: 4.00

ELE--- ---

Credit Hours: 3.00

FIRST YEAR
First Semester			Hours
CORE	AUT-048	Intro to Automotive Technology AUT-048 Intro to Automotive Technology This course is a study of chemicals, shop safety and operations, tools and equipment, and careers in automotive technology. Techniques associated with electrical/electronics, heating and air conditioning, engine repair, brakes, steering and suspension, and engine performance will be discussed. Course Outline +	2.0
CORE	AUT-050	Engine Repair AUT-050 Engine Repair This course is a study of engine design, diagnosis, removal, cylinder head and valve train repair. Short block repair, lubricating systems, cooling systems will be discussed and hands on reassembly of the engine is included. Course Outline +	5.0
CORE	AUT-051	Electrical Systems I AUT-051 Electrical Systems I This course is a study of the principles of electricity and electrical circuit design and diagnosing. Covers battery diagnosis and service. Starting Systems diagnosis and repair will be discussed. Course Outline +	4.0
CORE	AUT-080	Steering and Suspension AUT-080 Steering and Suspension This course is a study of steering systems, front and rear suspension systems. It also covers basic wheel alignment, diagnosis and repair culminating in complete four wheel computerized alignment. Course Outline +	4.0
	Semester Totals		15.0
Second Semester
CORE	AUT-052	Engine Performance I AUT-052 Engine Performance I This course is a study of computerized engine control system operation and diagnosis. Focusing on computer networks, sensors and ignition systems beginning with and building on basic ignition systems and culminating with computerized unit ignition systems. Course Outline +++	5.0
CORE	AUT-053	Brake Systems AUT-053 Brake Systems This course is a study of the hydraulic principles of drum, disc, and ABS brake systems. Diagnosis and repair of power assisted, drum, disc, and antilock brake systems will be discussed. Course Outline +++	4.0
ELE	--- ---	Career Elective --- --- Career Elective	3.0
	Semester Totals		12.0

Total Program Hours

27.0

Suggested Electives
AUT-076	Auto Transmissions/Transaxles AUT-076 Auto Transmissions/Transaxles This course is a study of automatic transmissions/transaxles maintenance, diagnosis and adjustment. On board and off board hydraulic control operations and repair are discussed. Course Outline	5.0
AUT-082	Manual Dr Train and Axles AUT-082 Manual Dr Train and Axles This course is the study of the diagnosis and repair of clutches, manual transmissions, transaxles and differentials. CV joints, drive shafts, front-wheel drive and four-wheel drive operations will be discussed. Course Outline	5.0
WEL-062	Welding Blueprint Read/Layout WEL-062 Welding Blueprint Read/Layout This course teaches students to read and interpret welding symbols and blueprints and to perform a minor welding layout. Math skills especially fractions are emphasized, reviewed and reinforced throughout this course. Course Outline	3.0
MTT-050	Intro to Machining Procedures MTT-050 Intro to Machining Procedures A study designed to highlight the theory and application of cutoff machines, drill press, engine lathe, milling machines, and basic benchwork involving layout and hand tools. Course Outline	3.0
IND-044	Fluid Power IND-044 Fluid Power Provides technician with basic concepts of pneumatics and hydraulics. This includes: fluid properties and laws, safety concerns, conductor types and sizing, pump operation and horsepower requirements, directional, pressure and flow control valves, fluid symbols. Trainers provide hands-on experience for students. Course Outline	3.0

Call Counseling Services: 217-234-5232
Email: counsel@lakelandcollege.edu

Faculty Contact: Kevin R. Miller
Faculty Email: kmiller@lakelandcollege.edu
Faculty Phone: 217-234-5286

* There are prerequisites, course requisites, or minimum placement test scores for this course.
** Electives must be approved by the Program Coordinator
+ Course only offered fall semester
++ Course only offered spring and summer semester
+++ Course only offered spring semester
++++ Course offered in summer term only
^ SOS 050 Human Relations and PSY 271 Introduction to Psychology cannot be used as a social science elective
^^ Consult Academic Advisor for appropriate course
^^^ Course requires a 30-hour practicum experience in addition to classroom lecture hours
^^^^ ECE 120 and ECE 125 must be taken the same semester

Suggested Electives
AUT-076	Auto Transmissions/Transaxles AUT-076 Auto Transmissions/Transaxles This course is a study of automatic transmissions/transaxles maintenance, diagnosis and adjustment. On board and off board hydraulic control operations and repair are discussed. Course Outline	5.0
AUT-082	Manual Dr Train and Axles AUT-082 Manual Dr Train and Axles This course is the study of the diagnosis and repair of clutches, manual transmissions, transaxles and differentials. CV joints, drive shafts, front-wheel drive and four-wheel drive operations will be discussed. Course Outline	5.0
WEL-062	Welding Blueprint Read/Layout WEL-062 Welding Blueprint Read/Layout This course teaches students to read and interpret welding symbols and blueprints and to perform a minor welding layout. Math skills especially fractions are emphasized, reviewed and reinforced throughout this course. Course Outline	3.0
MTT-050	Intro to Machining Procedures MTT-050 Intro to Machining Procedures A study designed to highlight the theory and application of cutoff machines, drill press, engine lathe, milling machines, and basic benchwork involving layout and hand tools. Course Outline	3.0
IND-044	Fluid Power IND-044 Fluid Power Provides technician with basic concepts of pneumatics and hydraulics. This includes: fluid properties and laws, safety concerns, conductor types and sizing, pump operation and horsepower requirements, directional, pressure and flow control valves, fluid symbols. Trainers provide hands-on experience for students. Course Outline	3.0

Suggested Electives
AUT-076	Auto Transmissions/Transaxles AUT-076 Auto Transmissions/Transaxles This course is a study of automatic transmissions/transaxles maintenance, diagnosis and adjustment. On board and off board hydraulic control operations and repair are discussed. Course Outline	5.0
AUT-082	Manual Dr Train and Axles AUT-082 Manual Dr Train and Axles This course is the study of the diagnosis and repair of clutches, manual transmissions, transaxles and differentials. CV joints, drive shafts, front-wheel drive and four-wheel drive operations will be discussed. Course Outline	5.0
WEL-062	Welding Blueprint Read/Layout WEL-062 Welding Blueprint Read/Layout This course teaches students to read and interpret welding symbols and blueprints and to perform a minor welding layout. Math skills especially fractions are emphasized, reviewed and reinforced throughout this course. Course Outline	3.0
MTT-050	Intro to Machining Procedures MTT-050 Intro to Machining Procedures A study designed to highlight the theory and application of cutoff machines, drill press, engine lathe, milling machines, and basic benchwork involving layout and hand tools. Course Outline	3.0
IND-044	Fluid Power IND-044 Fluid Power Provides technician with basic concepts of pneumatics and hydraulics. This includes: fluid properties and laws, safety concerns, conductor types and sizing, pump operation and horsepower requirements, directional, pressure and flow control valves, fluid symbols. Trainers provide hands-on experience for students. Course Outline	3.0

Auto Mechanic I (CRT.AUTO)

Catalog Term Year: 2023 Spring

First YearFirst Semester

First YearSecond Semester

AUT-048Intro to Automotive Technology

AUT-050Engine Repair

AUT-051Electrical Systems I

AUT-080Steering and Suspension

Semester Totals

AUT-052Engine Performance I

AUT-053Brake Systems

--- ---Career Elective

Semester Totals

Total Program Hours

AUT-076Auto Transmissions/Transaxles

AUT-082Manual Dr Train and Axles

WEL-062Welding Blueprint Read/Layout

MTT-050Intro to Machining Procedures

IND-044Fluid Power

AUT-076Auto Transmissions/Transaxles

AUT-082Manual Dr Train and Axles

WEL-062Welding Blueprint Read/Layout

MTT-050Intro to Machining Procedures

IND-044Fluid Power

AUT-076Auto Transmissions/Transaxles

AUT-082Manual Dr Train and Axles

WEL-062Welding Blueprint Read/Layout

MTT-050Intro to Machining Procedures

IND-044Fluid Power

First Year
First Semester

First Year
Second Semester

AUT-048
Intro to Automotive Technology

AUT-050
Engine Repair

AUT-051
Electrical Systems I

AUT-080
Steering and Suspension

AUT-052
Engine Performance I

AUT-053
Brake Systems

--- ---
Career Elective

AUT-076
Auto Transmissions/Transaxles

AUT-082
Manual Dr Train and Axles

WEL-062
Welding Blueprint Read/Layout

MTT-050
Intro to Machining Procedures

IND-044
Fluid Power

AUT-076
Auto Transmissions/Transaxles

AUT-082
Manual Dr Train and Axles

WEL-062
Welding Blueprint Read/Layout

MTT-050
Intro to Machining Procedures

IND-044
Fluid Power

AUT-076
Auto Transmissions/Transaxles

AUT-082
Manual Dr Train and Axles

WEL-062
Welding Blueprint Read/Layout

MTT-050
Intro to Machining Procedures

IND-044
Fluid Power